Question 1

Consistency is our priority. We maintain strict quality control protocols, standardized production processes, and comprehensive inspection procedures to ensure every batch meets the same high standards. Our recent factory renovation further enhanced our quality control capabilities

Accepted Answer

Batch-to-batch consistency is critical for commercial furniture projects where every unit must match — same dimensions, same finish, same structural performance. Here is how we guarantee it: Standardized Production Documentation:  •Every product has a locked production specification sheet: exact material grade, tube diameter, wall thickness, base geometry, and finish parameters •No deviation from spec sheet without written customer approval •Spec sheets archived per order and referenced for repeat production runs Process Controls for Consistency: •Single production run per batch: same material batch, same machine setup, same operator team for the entire order — eliminates intra-batch variation•Powder coating and electroplating performed in continuous batch runs, not split across sessions — ensures uniform color and finish depth•Welding parameters (current, voltage, wire feed rate) locked per product type and monitored per shift Color & Finish Consistency: •Pantone reference card maintained per custom color — used as visual standard at coating line•First-off sample at start of each coating batch compared against reference under D65 lighting•Mid-batch and end-batch color pull tests verify no drift across the run•Electroplating thickness measured per batch with minimum 3 sample points per 200 units Dimensional Consistency: •Key dimensions (height, base diameter, column diameter) measured on minimum 5% of units per batch•Any unit exceeding ±2mm tolerance from spec is flagged and corrected before packaging•Full dimensional report available per batch upon request What Happens If a Deviation Is Found: •Production paused immediately•Root cause identified (material, machine, operator)•Corrective action applied and verified before resuming•Affected units re-inspected 100% — no partial sampling for flagged issues•Corrective report documented and shared with you Our recent factory renovation established dedicated quality control stations, standardized measurement tool sets, and improved environmental controls (temperature, humidity) at coating and plating lines — all aimed at tighter consistency. Learn more about our capabilities at AEONTI.com or contact our team for batch consistency documentation.our

Question 2

Strict full inspection is carried out before shipment, covering multiple aspects such as raw materials, welding, surface treatment, load-bearing capacity, and packaging, to ensure product quality.

Accepted Answer

Yes. Every AEONTI product undergoes a multi-stage quality inspection process before shipment — not a final random check, but a systematic full-line protocol embedded into production.5-Stage Quality Inspection Process: Stage 1: Raw Material Inspection •Steel tube wall thickness measured with micrometer (tolerance ±0.1mm)•Material grade verification (Q235B, 201/304 SS, aluminum alloy) via composition testing•Incoming material rejected if dimensional or compositional deviations exceed threshold Stage 2: Welding Inspection •Visual weld seam inspection — no cracks, porosity, or undercut•Weld penetration depth verified for structural joints•All critical load-bearing joints 100% inspected, not sampled Stage 3: Surface Treatment Inspection •Powder coating: adhesion cross-hatch test to check coating bonding strength•Electroplating: thickness measurement and salt spray corrosion test•Brushed finish: uniformity and scratch-free visual inspection•Color consistency verified against Pantone reference under controlled lighting Stage 4: Load-Bearing Test •Static load test: each base loaded to 1.5× rated capacity for 30 minutes•No permanent deformation, joint failure, or base plate bending allowed•Test results recorded per batch with traceable inspection reports Stage 5: Packaging Inspection •Carton integrity: 5-layer corrugated board, no damage or moisture•EPE foam wrapping and corner protectors verified per unit•Labeling accuracy: correct SKU, quantity, and destination marking•Palletized shipments: steel strapping and stretch film integrity check Third-Party Inspection Welcome: We facilitate pre-shipment inspection by SGS, BV, TUV, or Intertek at your request. Inspection results are shared with you before final shipment approval. If any issue is found, we correct it before dispatch — no shipment proceeds without your clearance.Our recent factory renovation further enhanced our QC capabilities with dedicated inspection stations and improved testing equipment. View our products at aeonti.com/products-list.htm or contact our team for specific inspection documentation. Contact us to get a quick quote

Complete Table Systems for Commercial Spaces

Quality & Certifications

Are you looking for a reliable manufacturer?

Products

Customer Service

Company

Support

Complete Table Systems for Commercial Spaces